Remote Control Zone
Thank you for visiting RCRacingExtreme Feel free to look around.





Classifieds will show once you register with our site!









We would like to ask that you register on our site so you can ask the experts and be a part of a great michigan based RC FORUM!

ENJOY.


Buy, Sell, and Talk Remote Control
 
Contributing Members now have their own category to post private messages to michiganr-c.com members only.
HomeHome  HomeHome  CalendarCalendar  GalleryGallery  FAQFAQ  SearchSearch  RegisterRegister  Log inLog in  
December 2017
MonTueWedThuFriSatSun
    123
45678910
11121314151617
18192021222324
25262728293031
CalendarCalendar
Affiliates
Lipo Nitro RC Remote control
Lipo Nitro RC Remote control

Share | 
 

 slash 4x4 problem

View previous topic View next topic Go down 
AuthorMessage
bashdaslash

avatar

Posts : 118
Join date : 2012-04-15
Age : 20
Location : Rochester Hills

PostSubject: slash 4x4 problem   Mon May 21, 2012 5:35 pm

Back to top Go down
tntpoof

avatar

Posts : 73
Join date : 2012-04-16
Location : Trenton

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:11 pm

Here is ur solution....put motor in ur slash.. Remove set screw get some lipstick or liquid paper put small amount on set screw end that touch's motor shaft.on 4pm (noon is flat spot on shaft)..set pinion so mess is as close to 100% as u can get I have seen many and getting them to 80% is a test.tighten set screw so it leave some mark on shaft.. take a fiber wheel loon ur dremel and put a small nick in shaft does not have to be a long flat spot jut a indent.. put motor back in and run it til u cook it (JK) use some 272 red locktite,(u'll need heat to get it off) Best TnT
Back to top Go down
bashdaslash

avatar

Posts : 118
Join date : 2012-04-15
Age : 20
Location : Rochester Hills

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:15 pm

Ok thanks a lot
Back to top Go down
bashdaslash

avatar

Posts : 118
Join date : 2012-04-15
Age : 20
Location : Rochester Hills

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:21 pm

So i should notch the non- flat area with my dremel and put my set screw on that new spot ????
Back to top Go down
tntpoof

avatar

Posts : 73
Join date : 2012-04-16
Location : Trenton

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:22 pm

only thank me when it works.. I know it will..also get a New setscrew if its 4-40 I have some killer star locks..
Back to top Go down
tntpoof

avatar

Posts : 73
Join date : 2012-04-16
Location : Trenton

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:23 pm

YES To last post Notch it small...
Back to top Go down
bashdaslash

avatar

Posts : 118
Join date : 2012-04-15
Age : 20
Location : Rochester Hills

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:24 pm

k i will give it a try ... i have to order some new set screws and pinions though so it might be a little while.
Back to top Go down
tntpoof

avatar

Posts : 73
Join date : 2012-04-16
Location : Trenton

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 7:36 pm

FST and Keck have those in stock.. what are the setscrew size??

Its a 3x4.. ace hardware-lowes-Homedepot all have these and any hobby store ..
Back to top Go down
bashdaslash

avatar

Posts : 118
Join date : 2012-04-15
Age : 20
Location : Rochester Hills

PostSubject: Re: slash 4x4 problem   Mon May 21, 2012 9:58 pm

Its the stock traxxas pinion size grub screw. I just ordered some pinions that came with some but for now on ill just go to the hardware store and get like 20 haha.
Back to top Go down
Sponsored content




PostSubject: Re: slash 4x4 problem   

Back to top Go down
 

slash 4x4 problem

View previous topic View next topic Back to top 
Page 1 of 1

 Similar topics

-
» possible 4l60e problem?
» I need some help with a Nerf problem..
» power transformer problem - help?
» Don Juan Rehearsal...What's really the problem here?
» Please help me diagnose a running condition problem.

Permissions in this forum:You cannot reply to topics in this forum
Remote Control Zone :: General :: General Talk-
}